B & C Pillar Vinyl Protection
Please watch the video below:.
Looking for videos and guides on how to install your Abstract Ocean accessories in your Tesla Cybertruck? You've found the right place!
Please watch the video below:.
Please watch the video below:.
Please watch the video below, and don't forget:.
Please refer to the video below:.
Please refer to the video below, and note that these ship with a protective film over each cap, but because we've used a finish that helps resist mud and dirt adhering, it also means the film doesn't stick well either! So if the film has detached, th
Please refer to the video below, and pay attention to the installation, as it's a little different to most PPF installs (less slip solution).
Looking for Model 3/Y instructions? Please go here. With credit to Jason, one of our awesome customers, please refer to the video below to see where to route the cable in the Cybertruck. Please note, you'll need a 10ft USB-C to C cable (the one in th
Please refer to the videos below...they're a bit wordy, but buried in the waffle are some important tips & tricks. The long piece of PPF is like wrangling a snake, so please watch the relevant section to ensure your application is successful! Key poi
Installation is easy!. For the D-Rings, remove the existing bolt using a 15mm socket (like this), and use that to secure the D-Ring hook to the vault bed.
Please refer to the short video below:.
Our sunshade for your Cybertruck is easy to install, but like all of these things, you tend to have to 'fight' with them! Follow these tips to make installation a snap.
Please refer to the video below. It's a long one, but use the chapter markers to jump to the section you need. There's tips on how to remove bubbles and dust towards the end with the rear protect install.
Please refer to the quick video below. If the Armor is curled after shipping, just lay it out flat(ish) for a few minutes and it'll soon flatten out.
Please watch the quick video below. If the Armor is curled after shipping, just lay it out flat(ish) for a few minutes and it'll soon flatten out.
Please watch the videos below. If the Armor is curled after shipping, just lay it out flat(ish) for a few minutes and it'll soon flatten out.
Please refer to the video below and use the chapter markers to jump to the section you need. If the Armor is curled after shipping, just lay it out flat(ish) for a few minutes and it'll soon flatten out.
These are incredibly easy to install, just follow these steps:
Shown below is the position for each piece on your Cybertruck front bumper protection. If you're installing the full set, we recommend applying each piece in alphabetical order. Please watch the installation video - it’s super easy, but there’s a cou
Please watch the videos below. the first for the upper surfaces, the second for the lower surface. If the Armor is curled after shipping, just lay it out flat(ish) for a few minutes and it'll soon flatten out.
please refer to the video below. If the Armor is curled after shipping, just lay it out flat(ish) for a few minutes and it'll soon flatten out.
Please watch the quick video below - each side is a mirror of the other, so you just need to watch the first half :-).
Please watch the quick video below, installation just takes a few minutes for each side.
Sometimes it's necessary to stretch the Armor PPF to get the perfect fit, particularly on longer sections. This quick video shows how to do that, before starting, please ensure:.
Please watch the video below, each piece has some important tips. If you want the speedy version, watch the sections for the back panels, then skip to the right side, where I go through things much faster.
Please watch the video below to see how to assemble and install your storage containers.
Please refer to the short video below:.
Please review the FAQ here, and watch the video below:. Step by Step instructions AI generated from the video are below:. Unboxing:. Preparation:. Positioning:. Adhesion:. Removal:. Reinstallation:. Additional Tips:
Please watch the video below, and don't forget, always try to install in the sunshine (50-80f) if at all possible, it makes things much easier.
Please refer to the quick video below, there's some nuance to this kit vs. some of the other Xpel Armor kits. As always, try to install in the sun if possible, but if not, when the temperature is at least 60f/16c. Below follows an AI generated step b